DC 12V Timer Delay Relay Digital LED Display Programmable Multi-Function Trigger Time Circuit Control Cycle Switch PLC Module

Specification:Model: YYC-2S 24 commonly used functions to meet more application needs; can control solenoid valves, pumps, motors, strips, etc.Input voltage: DC 5/12/24V optionalOutput power: can control DC or AC load within 10ATime range: 0.01 seconds to 999 minutes adjustable at any timeWiring port description:1, DC+: input DC power supply positive2, DC-: input DC power supply negative3, IN+: signal input positive4, IN-: signal input terminal5, NO: Relay normally open interface, the relay is suspended before the suction, after the suction and short circuit with COM6, COM: relay common interface7. NC: The relay normally closes the interface, and the relay is shorted to COM before the suction is closed.Function list:P-11: Jog P-12: Self-locking P-13: Give signal, the relay will stop automatically for A seconds; the trigger will be invalid during the delay.P-14: Give the signal, the relay will stop automatically for A seconds; trigger the retime during the delay.P-15: Give the signal, the relay will stop automatically for A seconds; trigger the superimposed timing during the delay.P-16: Give signal, the relay will stop automatically for A seconds; trigger reset during delayP-17: Give signal, relay pull-in, input signal is disconnected, start timing, output is off after A secondsP-18: After power-on, the relay will immediately pull in, after a delay of A seconds, the power will be turned off;P-21: Disconnect the signal relay, after a delay of A seconds, the relay pulls inP-22: Give signal, after more than A seconds, the relay pulls in, the signal disappears, the relay stops.P-23: After the signal disappears for more than A seconds, the relay is closed, there is a signal, and the relay stops.P-24: There is a signal. After more than A seconds, the relay is closed. After the signal disappears for more than A seconds, the relay stops.P-25: There is a signal after more than A seconds, the relay is closed, and after a signal exceeds A seconds, the relay stops.P-26: There is a signal. The relay stops after A seconds of suction. The signal disappears and the relay stops again for A seconds.P-27: The pulse signal is detected and the relay is closed; if there is no pulse signal, the relay delays for A seconds;P-28: After power-on, after a delay of A seconds, the relay pulls in until the power is turned off.P-31: After power-on, the relay pulls in for A seconds, disconnects B seconds, infinite loop; power-off stops P-32: signal, start P-31P-33: Give a signal, start P-31 infinite loop; give another signal to terminate the loopP-34: After power-on, after a delay of A seconds, the relay pulls in and closes after B seconds.P-35: There is a signal. After a delay of A seconds, the relay pulls in and closes after B seconds.P-36: There is a signal. After more than A seconds, the relay pulls in and closes after B seconds.P-37: There is a signal, the relay will stop automatically for A seconds, and then stop for 24 seconds. The signal trigger is invalid during A+B time.P-38: There is a signal, the relay will stop automatically for A seconds, stop and re-clock for B seconds, and then automatically close for A seconds.P-41: There is no signal; the signal disappears; the relay works after the delay of A time.P-42: The signal disappears, after a delay of A time, the relay works; the end of work B timeP-43: The signal disappears. After the A time, the relay works; the working B time ends.P-44: After power-on, the relay works for A time and stops B time; the cycle stops automatically for C times.P-45: The power is not activated, after the signal is given; the relay works for A time, the B time is stopped; the cycle C stops automatically; the signal is given again, once againP-46: After the signal is sent for more than A times, the relay is closed; the suction is kept; the power is stopped.P-47: After the signal is sent for more than A times, the relay is closed for B seconds.P-48: In C seconds, after the signal is continuously sent for more than A times, the relay is closed for B seconds.Button setting instructions:The power-on display “————” means to enter the standby state;Press K1 for the first time (more than 1 second is required to prevent false triggering)Screen display: P -11: K2 adjusts the main mode, K3 and K4 adjustment functionsPress the second time K1, the screen displays: A001: K2 and K3 adjust the first time A, K4 adjust the decimal point (time unit)Pressing the third K1, the screen displays: B001: K2 and K3 adjust the second time B, K4 adjusts the decimal point (time unit)Pressing K1 for the fourth time, “————” means to enter the standby state;Press K4 in standby mode to permanently turn off/on the display and switch the low power mode.X.XX decimal point in hundred, timing range: 0.01 seconds to 9.99 secondsXX.X decimal point in ten, timing range: 0.1 seconds to 99.9 secondsXXX has no decimal point, timing range: 1 second ~ 999 secondsXXX. The decimal point is in one place, the time range is from 1 minute to 999 minutes.